4 x 12 W power amplifier with dynamic distortion detector and diagnostic interface

FEATURES
Requires very few external components
High output power
Fixed gain
Diagnostic facility (distortion, short-circuit and temperature detection)
Good ripple rejection
Mode select switch (operating, mute and stand-by)
Load dump protection
AC and DC short-circuit safe to ground and to VP
Low power dissipation in any short-circuit condition
Thermally protected
Reverse polarity safe
Electrostatic discharge protection
No switch-on/switch-off plop
Flexible leads
Low thermal resistance
Identical inputs.

GENERAL DESCRIPTION

The TDA8562Q is an integrated class-B output amplifier in a 17-lead single-in-line (SIL) power package. It contains 4 × 12 W single-ended amplifiers.

Circuit Diagram

4 x 12 W power amplifier with dynamic distortion detector and diagnostic interface

Read More

TL071 MOSFET Audio Amplifier 1 x 70w

TL071 MOSFET Audio Amplifier general description: 

   This simple mosfet power audio amplifier circuit, with TL071 and 2 mosfets (IRF9530, IRF530) power amplifiers can deliver up to 45W on 8 ohm. This schematic is based on Siliconix application and is based on variations of voltage on the 2 resistors serial inserted on the voltage supplier of the operational amplifier driver. The mosfet transistors must be mounted on a heatsink at least 1K/W.  Amplifier efficiency is 70%, distortions at cut frequency were at most 0.2% at 20Hz on 8 ohm and 10W. With a power supply of +/- 30V the mosfet audio amplifier can deliver 45W on 8 ohm and 70w on 4 ohm. Remember that this audio amplifier is not protected on short circuits so every time you switch on check to see if the speaker is connected.

MOSFET Audio Amplifier Circuit diagram:

Read More

4 x 11 W single ended car radio power amplifier

FEATURES

Requires very few external components

Flexibility in use Quad single-ended or stereo BTL

High output power

Low offset voltage at output (important for BTL)

Fixed gain

Good ripple rejection

Mute/stand-by switch

Load dump protection

AC and DC short-circuit-safe to ground and VP

Thermally protected

Reverse polarity safe

Capability to handle high energy on outputs (VP = 0)

Protected against electrostatic discharge

No switch-on/switch-off plop

Flexible leads

Low thermal resistance

Identical inputs (inverting and non-inverting).

GENERAL DESCRIPTION

The TDA1558Q is a monolithic integrated class-B output amplifier in a 17-lead single-in-line (SIL) plastic power package. The device contains 4 x 11 W single-ended or 2 x 22 W BTL amplifiers and has been primarily developed for car radio applications.

Circuit Diagram

Circuit diagram for  4 x 11 W single-ended car radio power amplifier

Read More

4 x 13 W single ended power amplifiers

FEATURES

Requires very few external components

High output power

Fixed gain

Diagnostic facility (distortion, short-circuit and temperature detection)

Good ripple rejection

Mode select switch (operating, mute and standby)

AC and DC short-circuit safe to ground and to VP

Low power dissipation in any short-circuit condition

Thermally protected

Reverse polarity safe

Electrostatic discharge protection

No switch-on/switch-off plop

Flexible leads

Low thermal resistance

Identical inputs.

GENERAL DESCRIPTION

The TDA8511J is an integrated class-B output amplifier in a 17-lead DIL-bent-SIL power package. It contains 4 × 13 W single-ended amplifiers.

Circuit Diagram:

4 x 13 W single-ended power amplifiers

Read More

TDA8922 Audio Amplifier 2 x 25W

TDA8922general description:

The TDA8922 is a high efficiency class-D audio power amplifier with very low dissipation. The typical output power is 2 × 25 W. The device is available in the HSOP24 power package with a small internal heatsink and in the DBS23P through-hole power package. Depending on the supply voltage and load conditions, a very small or even no external heatsink is required. The amplifier operates over a wide supply voltage range from ±12.5 to ±30 V and

consumes a very low quiescent current. TDA8922 Audio Amplifier 2 x 25W

TDA8922 features:

• High efficiency (∼90%)
• Operating supply voltage from ±12.5 to ±30 V
• Very low quiescent current
• Low distortion
• Usable as a stereo Single-Ended (SE) amplifier or as a mono amplifier in Bridge-Tied Load (BTL)
•  Fixed gain of 30 dB in Single-Ended (SE) and 36 dB in Bridge-Tied Load (BTL)
• High output power
• Good ripple rejection
• Internal switching frequency can be overruled by an external clock
• No switch-on or switch-off plop noise
• Short-circuit proof across load and to supply lines
• Electrostatic discharge protection
• Thermally protected.

TDA8922 aplications:

• Television sets
• Home-sound sets
• Multimedia systems
• All mains fed audio systems
• Car audio (boosters).

TDA8922 circuit:

TDA8922 layout and pcb:

TDA8922 datasheet:

Read More